เราใช้คุกกี้เพื่อปรับปรุงประสบการณ์การท่องเว็บของคุณ ในการใช้เว็บไซต์ของเราต่อไปคุณยอมรับนโยบายคุกกี้ของเรา

หุบ Close Cookie Notification
Instron
  • Back
  • Home
  • ผลิตภัณฑ์
    ระบบทดสอบ
    เครื่องทดสอบความแข็งแรงของวัสดุแบบอเนกประสงค์
    ความคงทนเชิงโครงสร้าง
    เครื่องทดสอบแบบอัตโนมัติ
    เครื่องทดสอบการเสียรูปและการอ่อนตัวของพล่าสติกเนื่องจากความร้อนและอุณหภูมิ ฆ
    ระบบจำลองการชนกระแทก
    เครื่องทดสอบแรงบิด
    เครื่องวัดความหนืดและการไหลของวัสดุในสภาพหลอมละลาย
    เครื่องทดสอบแรงกระแทกในแนวดิ่งและแบบฆ้อนเหวี่ยง
    เครื่องทดสอบแบบไดนามิคและความล้า
    รุ่นที่ไม่มีผลิตแล้ว
    อุปกรณ์เสริมในการทดสอบ
    ซอฟต์แวร์
    โหลดเซลล์วัดค่าแรงดึงแรงกด
    การลอก การเสียดทาน การเจาะทะลุ
    ตู้ควบคุมอุณหภูมิ และเตาควบคุมความร้อนสูง
    อุปกรณ์จับชิ้นงานทดสอบแรงดึง
    อุปกรณ์ทดสอบแรงดัดโค้ง
    อุปกรณ์ทดสอบแรงกด
    อุปกรณ์ทดสอบวัสดุทางการแพทย์
    อุปกรณ์วัดระยะยืด
    โหลดเซลล์วัดค่าแรงดึงแรงกด
    อุปกรณ์ทดสอบงานอิเล็คโทรนิคส์
    อุปกรณ์วัดและเตรียมตัวอย่าง
    อุปกรณ์เสริมทั้งหมด
    แคตาล็อกอุปกรณ์เสริม
  • โซลูชั่นอุตสาหกรรม
    ดูตามวัสดุที่ทดสอบ ดูตามมาตรฐานในการทดสอบ ดูตามประเภทการทดสอบ
    ดูตามกลุ่มอุตสาหกรรม
    ยานยนต์
    ชีวการแพทย์
    อิเล็กทรอนิกส์
    วัสดุ
    คอมโพสิต
    โลหะ
    พลาสติก
  • บริการและความช่วยเหลือ
    Instron Remote Technical Support วงรอบอายุของผลิตภัณฑ์ การฝึกอบรม
    บริการ
    การสอบเทียบและการสอบทวน
    ความช่วยเหลือในการใช้งานจาก Instron
    บริการด้านเทคนิค
    คำถาม คำตอบที่เจอบ่อยๆ
    บริการอัพเดตซอฟต์แวร์
    แหล่งข้อมูล
    คู่มือ
    การหาตำแหน่งของ เลขหมายประจำเครื่อง
  • บริษัทของเรา
    ตำแหน่งงาน ข่าวประชาสัมพันธ์ สมัครจดหมายข่าวจากเรา
    เกี่ยวกับเรา
    ประวัติของเรา
    ที่อยู่
    เอกสารรับรองสถานะ
    แหล่งข้อมูล
    ศัพทานุกรม
    ประเภทการทดสอบ
    จดหมายข่าว
    แหล่งข้อมูลทางเทคนิค
    ข่าวสาร
    กิจกรรม
    ข้อมูลนำเสนอทางเว็บ
    กรณีศึกษา
  • ติดต่อเรา
  • ประเทศไทย
คำตอบของการทดสอบ » ตามประเภทการทดสอบ » รีโลโลยี » ISO 1133-2 & ASTM D1238

ISO 1133-2 and ASTM D1238: When Load Cell Ensures Repeatability of Results

Standard

  • ISO 1133
  • ASTM D1238

Specimen

  • เม็ดพลาสติก
  • ผง

Test Types

  • รีโอโลยี

Materials

  • พลาสติก
  • ยาง/อิลาสโตเมอร์

Business Sector

  • ผลิตภัณฑ์อุปโภคบริโภค/อุตสาหกรรม
  • บริการรับจ้างทดสอบ
Contact usView Accessories Catalog
MF 20
  • MF 20
  • Description
  • Literature

Melt Flow Rate (MFR) and Melt Volume-Flow Rate (MVR) can normally be obtained with easy and quick test procedures. Test standards specify detailed test conditions, including pre-heating period, starting position, and measurement length/time. However, when using a basic melt flow tester (extrusion plastometer), fulfilling all standard specifications can be challenging with some polymers and compounds, and results can be affected by poor repeatability.

It's not uncommon that during the pre-heating period the sample swells and pushes the piston up, especially when testing under low-load conditions (e.g. less than 2.16 kg). Applying a compacting force higher than the test weight can prevent this from happening, and if precise positioning of weight lifting device is possible, the starting position and timing for measurements can be set in a much more repeatable way.

Some samples show very high viscosity and effective compacting requires high loads. Air bubbles trapped inside as a result of poor compacting can affect the MFR/MVR results. A high, but controlled, compacting force is needed. Plus, at the end of tests, the same force can be applied for purging out the remaining material, reducing the total test cycle time.

We tested an HDPE sample with an expected MFR of about 0.25 g/10 min (190 °C, 2.16 kg) with a CEAST MF30, applying ISO 1133-2 Procedure B. CEAST MF30 has a load cell integrated with the weight lifting device, giving the possibility to apply up to 750 N of compacting force. To compare the repeatability of results, we performed twenty consecutive tests using the load cell for compacting, and another twenty without (so using only the test weight to compact). The average MFR result was close to the expected value in both cases. However, results from the tests performed without the load cell were consistently higher and with a standard deviation of 0.012 g/10 min (close to 5%), whereas tests where the load cell was compacted the standard deviation was as low as 0.005 g/10 min (2%). Similar results were obtained also following ASTM D1238 Procedure B.

CEAST Melt Flow Series Brochure

Flow properties of molten plastics are a critical characteristic requiring good knowledge and control. The Instron® Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Mass-Flow Rate (MFR) and the Melt Volume-Flow Rate (MVR). CEAST Melt Flow Testers range from systems that perform a simple manual test procedure to semi-automated testing systems performing multiple weight tests.

  • ผลิตภัณฑ์
  • 7/3/2013
  • 1.1 MB

เลือกพื้นที่

Dismiss Region Selector

Americas

  • North America
  • Brasil
  • South America

All Other Countries

  • Global Site

Europe

  • France
  • Deutschland
  • Italia
  • Polska
  • España
  • Türkçe
  • United Kingdom

Asia Pacific

  • 中国
  • India
  • 日本
  • 대한민국
  • 台灣
  • ประเทศไทย
Instron Logo White
ข้อมูลติดต่อ

184/141 อาคารฟอรัมทาวเวอร์ ชั้น 23
ถนนรัชดาภิเษก แขวงห้วยขวาง เขตห้วยขวาง
กรุงเทพมหานคร 10310

ฝ่ายขาย:  66 2754471-2

ฝ่ายบริการ:  66 2754471-2

ทั่วไป:  66 2754471-2

ลิงค์ที่เป็นประโยชน์
  • เครื่องทดสอบ
  • ซอฟต์แวร์
  • อุปกรณ์เสริม
  • แคตาล็อก
  • ศัพทานุกรม
  • ไลบรารี
  • สูตรสำเร็จในการทดสอบ
  • จดหมายข่าว
  • ข้อมูลนำเสนอทางเว็บ
  • กรณีศึกษา
  • กิจกรรม
  • ตำแหน่งงาน
Policies / Legal
  • นโยบายความเป็นส่วนตัวและคุ้กกี้
  • เงื่อนไขการใช้งาน
  • การควบคุมการส่งออก
  • GDPR ประกาศแจ้งเกี่ยวกับข้อมูล
ร่วมเป็นเครือข่ายกับเรา
สมัครจดหมายข่าวจากเรา
อีเมลแอดเดรส
© Illinois Tool Works Inc. สงวนลิขสิทธิ์
[email protected]
  • นโยบายความเป็นส่วนตัวและคุ้กกี้
  • เงื่อนไขการใช้งาน
  • การควบคุมการส่งออก
  • GDPR ประกาศแจ้งเกี่ยวกับข้อมูล